Small adjustable submersible pump for hydroponics, 600 L/h
This submersible water pump, the Sicce Micra Plus, delivers up to 600 L/h at 6.5 W, with an adjustable flow rate and a 13 mm outlet for 12 x 16 mm pipe. It is the original pump for the CultiMate Aero aeroponic pot and the Ebb&Grow flood table, and it suits any small hydroponic or aquaponic system.
Made in Italy, it comes with a 2-year guarantee, excluding the rotor.
The summary
- What you receive: a Sicce submersible pump rated at 600 L/h and 6.5 W, with suction cups, filter sponge, and pipe adaptor.
- Actual flow rate: 600 L/h when water exits at pump level, decreasing progressively as head height increases, and zero at around 80 cm.
- Compatible systems: the original pump for the CultiMate Aero and the Ebb&Grow, and small aquaponic tanks.
- Maintenance: rinse the impeller every 2 to 3 months, and never run the pump dry.
Small submersible pump for circulating the solution in a hydroponic system or an aquaponic tank
A submersible pump circulates the nutrient solution of a hydroponic system, whether it is feeding sprinklers, filling an ebb-and-flow table or sending water back to a grow bed. This 600 L/h pump, made in Italy by Sicce, is the original equipment in the CultiMate Aero aeroponic pot and the Ebb&Grow ebb-and-flow table. Compact, at 57 mm long by 43 mm wide and 52 mm high, it sits on the bottom of the sump tank on its suction cups, and you adjust its flow rate by hand to suit the needs of your system.
📏 Flow rate by head height
The flow rate of 600 L/h applies at zero head, that is, when the water leaves at the level of the pump. As soon as the pump pushes the water upwards, the flow rate drops, slowly at first and then faster and faster, until it falls to zero at around 80 cm of height. The higher the outlet, the further the real flow rate falls below the stated 600 L/h. Bends, a long pipe or sprinklers add resistance that reduces this flow rate further. Before choosing a pump, you should therefore measure the height between the water level in the sump tank and the highest outlet point.
This flow rate suits small systems. In a 45-litre aeroponic pot, the pump feeds the diffusers that keep the roots under a continuous mist, and in an ebb-and-flow table it fills the grow bed before the solution returns to the sump tank by gravity. It can also be used to stir a deep water culture tank or to run a small fountain. For a larger or higher system, the 1,200 to 3,400 L/h pond pump takes over.
Replacing the pump of an aeroponic pot
The CultiMate Aero aeroponic pot works with this precise pump, connected to its riser tube and its diffusers. If it fails or wears out, it fits in exactly the same way in the aeroponic pot, with no adaptation of the pipework. You therefore keep the flow rate the sprayers and diffusers were designed for, and the system returns to its original operation without any further adjustment.
Never run the pump dry
The pump works only when submerged, as running it dry damages its motor. Water must always cover its intake grilles, around 2 cm at the very least, and you should keep an eye on the level in the sump tank, which drops through evaporation and plant uptake. Connect it behind a 30 mA residual current device, with a drip loop on the cable. The water must not exceed 35 °C.
Adjustable flow rate
A sliding regulator reduces the flow rate, which stops a small grow bed from flooding and keeps the solution from being thrown out of the sprinklers.
The 13 mm outlet
It takes a flexible 12 x 16 mm hose thanks to the supplied adaptor, or a rigid 13 mm pipe.
Suction cups
They hold the pump at the bottom of the sump tank and absorb vibration, which limits the noise transmitted to the tank.
Its synchronous motor draws 6.5 W, which comes to around 4.7 kWh per month in continuous operation, a modest figure for a pump that runs day and night in an aeroponic system. The rotor shaft is made of AISI 316 stainless steel, which withstands slightly acidic nutrient solutions. A filter foam placed in the pre-chamber catches debris before it reaches the rotor, and the 1.5 m cable ends in a European two-pin plug. You can leave it running 24 hours a day, as long as it remains submerged.
🔧 Rotor maintenance
Limescale and nutrient solution deposits eventually slow the impeller, which reduces the flow rate and then jams the pump. The filter foam should be rinsed as soon as the flow rate drops: slide out the pre-chamber located beneath the pump and run it under water. Every 2 to 3 months, unplug the pump, remove the front cover and then take out the impeller to rinse it in lukewarm water, before reassembling everything in reverse order. The cable cannot be replaced, so a damaged cable means replacing the pump. The 2-year warranty covers the pump, but not the impeller, which is considered a wear part.
🐟 In aquaponics and in an aquarium
Originally designed for aquarium keeping, this pump is also suitable for a system with fish. In a small aquaponic set-up, it lifts water from the pond to a grow bed filled with clay pebbles, placed no more than 40 cm above, which is half its maximum head, leaving a margin for losses in the pipe and elbows. The regulator then lets you adjust the flow rate so that the grow bed fills without overflowing. With small fish, keep the filter foam in place and clean it more often, as waste loads it up quickly.
🪣 Tank volume and cut-off
With fish, the flow rate is judged by the volume of the tank. The FAO guide to small-scale aquaponics advises passing this volume through the system once an hour when the tank is lightly stocked, and twice an hour when it is densely stocked. To find out what the pump really delivers at your head height, fill a graduated container for one minute at the pipe outlet, then multiply by 60: you are then comparing a measured flow rate, not the flow rate at zero head. The pump runs continuously, so a power cut also stops the movement of the water and depletes the tank of oxygen. A battery-powered backup air pump installed next to the tank starts on its own in this situation and keeps the water aerated until the power returns.
📦 In the box
The pump is supplied with its 1.5 m cable and plug, suction cups, filter sponge, adapter for 12 x 16 mm pipe and multilingual instructions, which include French. It runs on 220 to 240 V and 50 Hz, and weighs about 320 g. Its manufacturer's reference is PRM220, and its spare rotor has the reference SGR0001. To oxygenate the solution as well as circulate it, you can add an aquarium air stone to the sump tank, which the pump does not replace.
Technical specifications
The flow rate
- Maximum flow rate
- 600 L/hAt zero height
- Maximum height
- 0.8 mNo flow rate at this height
- Motor
- SynchronousPermanent magnet
- Flow rate adjustment
- Yes, via a regulator
- Water temperature
- 35 °C at most
- Rotor shaft
- AISI 316 stainless steel
Power supply
- Power
- 6.5 W
- Voltage
- 220 to 240 V, 50 Hz
- Cable
- 1.5 mNon-replaceable, indoor use
- Continuous consumption
- Around 4.7 kWh a month
The pump
- Dimensions
- 57 x 43 x 52 mm
- Weight
- 320 g
- Outlet
- 13 mm12 x 16 mm pipe with the adapter
- Warranty
- 2 yearsRotor not included
- Manufacturer's reference
- Sicce PRM220EAN 8011469990841
- Manufacture
- Italy
To allow for in addition
- Oxygenation
- An aquarium air pump
- Grow medium in aquaponics
- Some clay pebbles
10 further specifications are available in the detailed view.
In the box
- 1 submersible pump with a 1.5 m cable
- 1 filter foam and its suction cups
- 1 adapter for 12 x 16 mm pipe
- 1 multilingual instruction leaflet
Manufacturer's values (Micra Plus instructions and data sheet for the 230 V version).
Manufacturer and product safety
- Manufacturer
- SICCE S.r.l. (TVA IT02883090249)
- Postal address
- Via V. Emanuele 115, 36050 Pozzoleone (VI), Italie
- Contact
- info@sicce.com (service client support@sicce.com) ; +39 0444 462826
- Website
- www.sicce.com
Information provided under Regulation (EU) 2023/988 on general product safety.
Documents & manuals
Manufacturer's instructions, multilingual including English
The instruction leaflet covers installation, flow adjustment, rotor cleaning, and the pump's warranty conditions.
Document not showing? Some publishers block display inside a frame, so open it in a tab.
Estimate your
delivery time
Your estimate
It covers preparing your order and then the transit time quoted by the carrier, counted in working days.
It is not a guaranteed delivery date: public holidays, peak periods, customs or a carrier delay can extend it. The exact amount, in your currency, is worked out in the cart once your address is entered.
Pump dispatched by tracked parcel from France. Exact shipping costs and final delivery times are displayed at checkout once your address has been entered. Outside the European Union, import duties and taxes are the responsibility of the recipient.
Frequently asked questions
8 questions
6 key questions, 8 in the detailed view
You may also like
Let us talk about your project
A question about this product or your setup? Our team will answer and advise you.
Interest-free instalment payments
Offered depending on the cart amount, at checkout.
Delivery in 2 to 15 working days
Depending on the products and shipping sites. Estimate by destination in the estimator on this page.
After-sales service 7 days a week by email or chat
Our team answers all your questions.
Shop responsibly
Become part of the change.








