Square horticultural LED panel, 200 or 300 W
This Lumatek square LED panel lights a grow bed, a hydroponic tray or a corner of an indoor vegetable garden of 80 x 80 or 100 x 100 cm. Its supplied dimmer offers four levels, from seedlings through to tomatoes in production, and the panel, protected to IP65, needs no fan.
The summary
- What you receive: the panel and its power supply, the mains cable, a dimmer and two metal hangers.
- How to choose: the 200 W for 80 x 80 cm, the 300 W for 100 x 100 cm.
- The light: 4000 K white supplemented with 660 nm red and 730 nm far-red, 508 or 816 µmol/s.
- The adjustment: four intensity steps, from 25 to 100%, to tailor the light to the crop.
- The height: 15 to 40 cm above the plants, perfectly level.
- In aquaponics: above the grow bed, never above the fish tank, in air free of condensation.
Full-spectrum grow light for a square indoor grow bed
The ATS Pro, also known as the Attis Pro, is a square LED panel designed by the British brand Lumatek. The diodes are spread across an aluminium plate measuring 52 or 56 cm per side and only 7 cm thick, which also acts as a heat sink: heat is dissipated through the surface of the panel, with no fan. A layer of clear resin covers the diodes and protects them from dust and water jets, in line with the IP65 rating. The panel is sold in two power ratings, 208 W for an area of 80 x 80 cm and 310 W for 100 x 100 cm, both supplied with their power supply and a dimmer.
This square format meets a specific need: lighting an indoor grow bed evenly, from seedling to harvest, without having to change the lamp during the season. The same panel raises your seedling trays at low intensity, brings on your salad leaves and herbs at half power, then supports the flowering of your tomatoes or strawberry plants at full power. You gain flexibility, since the setting follows the crop of the moment instead of forcing a single use on you.
🌈 Three colours of LEDs
The light combines three families of LEDs. The 4000 K white LEDs provide most of the output and cover the whole visible spectrum, from blue to red: 288 on the 200 W, 576 on the 300 W, where they draw 74% of the power. Red LEDs at 660 nm, the most efficient wavelength for photosynthesis, boost the growth and flowering of your fruiting vegetables: 12 on the 200 W, 24 on the 300 W. The 24 far-red LEDs at 730 nm complete the set; this almost invisible light speeds up leaf expansion and the switch to flowering. The photosynthetic photon flux reaches 508 µmol/s for the 200 W and 816 µmol/s for the 300 W, with an efficacy of 2.5 and 2.7 µmol/J.
A contactor timer for the day length
The dimmer controls the intensity; for the duration, the instructions call for a contactor timer, suited to the inrush current of the power supply, rather than a household plug-in timer. Set it to 14 to 16 hours for seedlings and leafy greens, and 12 hours for fruiting vegetables in flower. The ratchet hangers then let you raise the panel by a few centimetres as the plants grow, without unhooking the whole assembly.
📐 Choosing between 200 and 300 W
The choice depends first of all on the area to be lit. The 200 W covers a square of 80 x 80 cm: a hydroponic tray, a small grow bed or a grow room of that size. The 300 W covers 100 x 100 cm, the size of a family aquaponic grow bed. Measured over the whole area, the average intensity received by the plants reaches, under the 200 W, about 577 µmol/m²/s at 30 cm and 479 at 50 cm over 80 x 80 cm; under the 300 W, about 622 µmol/m²/s at 30 cm and 524 at 50 cm over 100 x 100 cm. Salads and herbs are content with 200 to 400 µmol/m²/s, while tomatoes in production benefit from higher values: the dimmer therefore lets you serve both with the same panel.
Condensation-free air, a protected socket
The instructions do not permit the panel to be used in a wet room, outdoors or under a fogger, and specify 20 to 90% humidity, without condensation. Plug it into a socket protected by a 30 mA residual current device, keep the mains plug and the contactor out of reach of water from the tray and from watering, and leave a drip loop in the cable before the socket. Unplug the panel before moving or cleaning it, then let it cool for 20 to 30 minutes.
☀️ Dosing the light to suit the crop
Your plants respond to the total amount of light received over the day, which horticulturists call the daily light integral and measure in moles of photons per square metre per day. It is easily calculated: intensity in µmol/m²/s, multiplied by the number of lighting hours and then by 0.0036. In protected cultivation, a lettuce grows well at between 12 and 17 moles a day, beyond which the edges of young leaves may brown, whereas tomato and pepper need 20 to 30 moles and strawberry 17 to 20. The dimmer and the hanging height are therefore there to help you aim for the right range rather than to light at maximum.
Seedlings and microgreens
At 25 or 50% power and a height of 40 cm, the light is sufficient for seedling trays without scorching the cotyledons.
Salad leaves and herbs
At around 50%, 16 hours a day, a lettuce stays within its range of 12 to 17 moles without tip burn.
Tomatoes and peppers
At full power, 12 hours a day at 30 or 40 cm, fruiting vegetables receive 25 moles or more.
Strawberry plants
At between 75 and 100% depending on the height, a planter of strawberries reaches its 17 to 20 moles per day.
If you hang the 300 W at 40 cm above a 1 m grow bed, it delivers on average 572 µmol/m²/s there at full power. Switched on for 12 hours, it provides about 25 moles per day, which suits tomatoes; switched on for 16 hours, it provides nearly 33, which is double what a lettuce can tolerate. For salad crops, therefore, turn the dimmer down towards 50%, or keep full power and shorten the duration, watching the edges of the young leaves. The 200 W at 40 cm, with its 511 µmol/m²/s, follows the same logic over an 80 cm square. These figures are averages across the whole surface: plants in the centre receive slightly more than those in the corners.
🐟 The aquaponic grow bed
A 1 x 1 m grow bed filled with clay pebbles, placed above or beside the fish tank, sits exactly under the area covered by the 300 W panel. The IP65 rating protects the panel from splashes, but the humidity rising from the water means you must ventilate the room so that no condensation forms on the resin. An oscillating clip-on fan circulates the air between the foliage and the panel. The salad leaves, herbs and fruiting vegetables there draw the nitrates that the bacteria produce from the fish waste, so plant growth, supported by the light, also helps maintain water quality.
Aim the light at the plants and keep the fish tank in the shade, because heavily lit water becomes covered in algae that use up part of those nitrates. An opaque lid or a simple sheet laid over the tank is enough, as long as you leave an opening for the water inlet and for aeration. If you want to grow tomatoes under this panel, the article on tomatoes in aquaponics covers pruning and pollination.
All the electricity consumed ends up as heat, about 310 W for the 300 W model at full power, the equivalent of a small supplementary heater. If your room is closed, this heat warms the air, speeds up plant transpiration and evaporation from the tray, and it can push the temperature above the 25 °C maximum specified for full power. Ventilate the room or install an air extraction system, especially in summer, and lower the intensity on hot days. In winter, this heat becomes a useful contribution to a cool room, though it does not replace heating the fish water, which is set up separately.
🔌 Installation and control
The panel hangs level from the two steel cables supplied, 15 to 40 cm above the plants, and plugs into a 230 V socket. The dimmer, which attaches with a hook-and-loop strip close by, offers four settings in addition to off: 25, 50, 75 and 100%. On the 300 W, these steps bring consumption down from 307 W to 227, 150 and then 80 W, and on the 200 W from 208 W to 150, 96 and then 50 W. The panel also accepts a 0-10 V control, such as the Lumatek Digital Panel Plus controller, which can drive up to one hundred fixtures with gradual sunrise and sunset. You can use it on its own in a windowless room, or to supplement the light from a conservatory in winter.
🧽 Maintenance and lifespan
The manufacturer quotes more than 60,000 hours for its diodes, around ten years at 16 hours a day, and guarantees the panel for 3 years. Maintenance is limited to dusting the light-emitting face and the fins, with the panel unplugged and cooled, using a soft, slightly damp cloth: a resin clouded by dust or limescale deposits lets less light through. Also check the condition of the hanging cables and the mains cable from time to time, especially if your room is damp and condensation forms there every night.
📦 What the box contains
The box contains the ATS Pro panel and its power supply, a 230 V mains cable, a 0-10 V dimmer with a hook-and-loop fastener, two metal suspension cables and the instructions, written in French among other languages. The contactor timer and, if you want to raise the panel without unhooking it, a pair of ratchet hangers are chosen separately. In a 100 cm grow tent, the 300 W model lights exactly the floor area.
Technical specifications
Lighting
- Photosynthetic flux
- 508 or 816 µmol/s200 W or 300 W
- Yield
- 2.5 or 2.7 µmol/J
- Spectrum
- White 4000 K, red 660 and 730 nm
- LEDs
- 324 or 624 diodesWhite 288 or 576, red 12 or 24, far-red 24
- Lighting angle
- 120°
- Intensity at 40 cm
- 511 or 572 µmol/m²/sAverage over 80 x 80 or 100 x 100 cm, at full power
The panel
- Power consumption
- 208 or 310 W
- Dimensions
- 52.5 or 56 cm per side, 7.2 cm thick
- Weight
- 4 or 5.2 kg
- Protection
- IP65, passive cooling
- Lifespan
- More than 60,000 h3-year manufacturer's warranty
- Compliance
- CE, RoHSPhotobiological safety to EN 62471
Usage
- Illuminated area
- 80 x 80 or 100 x 100 cm
- Dimming
- 25, 50, 75 and 100%Or external 0-10 V control
- Feeding
- 220 to 240 V, 50/60 Hz
- Maximum ambience
- 25 °C at full powerReduce the intensity if the room is warmer
- Height above the plants
- 15 to 40 cmPanel suspended horizontally
- Air humidity
- 20 to 90 %, non-condensingNeither a mister nor a soaked room
To allow for in addition
- Timer
- Contactor timerSuited to the panel's inrush current
- Height adjustment
- Ratchet hangersTo raise the panel as the plants grow
12 further specifications are available in the detailed view.
In the box
- 1 ATS Pro panel with its power supply
- 1 230 V mains cable
- 1 0-10 V dimmer with hook-and-loop fastening
- 2 metal suspension cables
- 1 instruction leaflet
Manufacturer's values (ATS 200 W Pro and ATS 300 W Pro datasheets, ATTIS 300 W Pro manual). Light benchmarks per crop based on Cornell University's CEA group; daily integrals calculated.
Manufacturer and product safety
- Website
- www.lumatek-lighting.com
Information provided under Regulation (EU) 2023/988 on general product safety.
Documents & manuals
ATS 300 W Pro manual, in French
Assembly, suspension height, dimming, maintenance, safety and warranty, in six languages including French.
Document not showing? Some publishers block display inside a frame, so open it in a tab.
Estimate your
delivery time
Your estimate
It covers preparing your order and then the transit time quoted by the carrier, counted in working days.
It is not a guaranteed delivery date: public holidays, peak periods, customs or a carrier delay can extend it. The exact amount, in your currency, is worked out in the cart once your address is entered.
The panel is dispatched in its original box with its power supply and accessories, from a distributor's warehouse in France. The exact shipping cost is shown in the basket.
Frequently asked questions
12 questions
6 key questions, 12 in the detailed view
You may also like
Let us talk about your project
A question about this product or your setup? Our team will answer and advise you.
Interest-free instalment payments
Offered depending on the cart amount, at checkout.
Delivery in 2 to 15 working days
Depending on the products and shipping sites. Estimate by destination in the estimator on this page.
After-sales service 7 days a week by email or chat
Our team answers all your questions.
Shop responsibly
Become part of the change.










