Solid white end cap for a 100 x 50 mm NFT channel seen from the front, with a small hole in the upper part

Solid end cap for a 100 x 50 mm NFT channel seen from the inside, with its interlocking edges

White outlet cap for a 100 x 50 mm NFT gutter seen from the front, with its 32 mm outlet sleeve

Outlet cap for a 100 x 50 mm NFT gutter seen from the inside, round opening in the plate

White joiner for connecting two 100 x 50 mm NFT channels end to end, three-quarter view

End caps and joiner for 100 × 50 mm NFT gutter

Dhs. 15.00

Quantité	Price	Price per unit	vs Lot de 8
Lot de 8	Dhs. 118.00	Dhs. 14.75	—
Lot de 16	Dhs. 223.00	Dhs. 13.94	−5 %

Dhs. 5.00 × 3 with no fees Klarna.

These three parts fit a 100 × 50 mm profile NFT gutter: the solid cap closes the head of the channel, the outlet cap returns the solution through a 32 mm socket, and the joiner connects two channels end to end.

Ref. SI-NFT105T01·Hydroponic spare part

Pièce : Bouchon plein

Bouchon plein

Bouchon de sortie 32 mm

Jonction

Quantité : Unité

Unité

Lot de 8

Lot de 16

Customer support 7 days a week by email

Delivery within 2 to 15 business days

100 % secure payment

The summary

What they are: the three parts that close, drain and extend a 100 x 50 mm NFT channel.
How many to buy: one blanking cap and one outlet cap per line, and one joiner between two channels.
How to fit them: with PVC cement or silicone, after a test with clean water.
How they arrive: singly, in packs of 8 or 16, part by part.

Solid plug, outlet plug and joiner for a 100 x 50 mm NFT channel

An NFT gutter supplied without end caps arrives open at both ends, and it is up to you to decide how it closes, where it drains and what it connects to. These three moulded parts with a 100 x 50 mm profile each answer one of those questions. You choose them separately, singly or in a set, depending on the number of lines you are building.

🧩 Three parts, three roles

Solid plug

It closes the head of the channel, on the side where the solution arrives, and stops light reaching the roots.

Outlet plug

It closes the lower end of the channel and lets the solution drain back to the tank through a 32 mm sleeve.

Junction

It joins two channels end to end, which lengthens a line without an intermediate end to seal.

The count is made per line, not per channel. A growing line, whether it has one channel or several, needs one solid end cap at its high point and one outlet cap at its low point, while each connection between two channels needs a coupling. For three 2 m channels placed end to end, that is 6 m of growing length, you should therefore allow for one solid end cap, one outlet cap and two couplings. Beyond a dozen metres, it is better to open a second line, because the plants at the end would receive a solution already depleted by those at the start.

💧 Watertightness and fittings

These parts slot onto the profile, then are sealed with PVC cement or silicone so they do not weep. The choice depends on the future of your line: silicone can still be removed if you reconfigure it, whereas PVC cement holds for good. In both cases, the perforated channel lid stays removable, since the seal only concerns the body of the gutter. Finally, the sleeve of the outlet cap takes a 32 mm polypropylene push-fit fitting or a PVC fitting of the same diameter, which carries the solution to your reservoir.

The unbounded gutter to be fitted out

These parts are made for the 100 x 50 mm NFT channel, 2 m, without end caps, supplied open at both ends with its perforated lid and its pots. Cut it to the length of your support if needed, then close the head end with the plain cap and the foot end with the outlet cap. If you would rather have a channel sealed at the factory, the module with glued end caps arrives ready-fitted and needs none of these parts.

A trial with clear water before gluing

Dry-fit each piece, lay the channel at its slope, then run clean water along the whole line before sealing anything. A leak at a joint then shows up straight away and can be fixed on an empty channel. Once the PVC glue has set, the piece cannot be taken apart again.

🐟 The return to the pond

In aquaponics, the solution leaving the outlet cap returns to the pond or to the sump, and the 32 mm pipe that carries it keeps its slope all the way so that no deposits are left behind. The two caps also play a less obvious role, because they shut the channel off from light. Water exposed to light quickly turns green, and algae then reach the root zone before passing into the pump. A properly closed channel therefore keeps the water clearer, which matters all the more when that water is heading back to your fish.

Technical specifications

The essentials

Solid plug: Closes off the head of the line
Outlet plug: 32 mm sleeveIt takes a PP push-fit fitting or a 32 mm PVC fitting.
Junction: Joins two channels end to end
Compatibility: NFT gutter 100 x 50 mmThe profile is measured overall, width then height.
Sealing: PVC adhesive or siliconeThe channel lid stays removable after bonding.
Origin: Italy

To budget for separately

Outlet fitting: 1 32 mm fitting per line
Gutter: NFT gutter 100 x 50 mm without end caps

In the box

1, 8 or 16 pieces of the chosen model, plain cap, outlet cap or junction, depending on the pack size.

Roles, 32 mm sleeve, compatibility and sealing recorded from the manufacturer's sheets, growrillahydroponics.com, on 08/10/2026. Line length: FAO guide to small-scale aquaponic production (2014).

Estimate your
delivery time

This is a lightweight, compact part that ships on its own or alongside a channel in the same parcel. Orders are dispatched from the workshop in Robassomero, near Turin. Exact shipping costs and delivery times are shown at checkout once you have entered your address. Outside the European Union, import duties and taxes are the responsibility of the recipient.

Frequently asked questions

6 questions

6 key questions

Will these parts fit a 100 x 80 mm gutter?

How many pieces do I need for my line?

Do they need to be glued?

Which pipe should be connected to the outlet cap?

How do you set up a line of several channels?

Can the lid be removed once the pieces are glued?

Let us talk about your project

A question about this product or your setup? Our team will answer and advise you.

Email us Contact form

Interest-free instalment payments

Offered depending on the cart amount, at checkout.

Delivery in 2 to 15 working days

Depending on the products and shipping sites. Estimate by destination in the estimator on this page.

After-sales service 7 days a week by email or chat

Our team answers all your questions.

Shop responsibly

Become part of the change.

End caps and joiner for 100 × 50 mm NFT gutter

The summary